Job scheduling limitations based on Date range (scheduling by day(s) range) by Operational level on Route
Current D365 job scheduling allows the Scheduling team to schedule jobs backward for a delivery date to prevent them from extending the scheduled production jobs into the follow date. This is a means of preventing Jobs that have processes which must be completed in a singular day (possibly due...
Sorting of indirect activities
Currently, indirect activities are sorted on the Production floor execution according to there Job-ID. However, it can happen that after a while an additional indirect activity is created, which should be after a similar indirect activity. Therefore it would be helpful if you could add a rang-...
Thank you for your feedback.
Currently this is not in our roadmap; however, we are tracking it and if we get more feedback and votes, we may consider it in the future.
Sincerely,
Johan Hoffmann
PM,
Microsoft.
The setup time and the run time for secondary operations are considering the load.
The setup time and the run time from secondary operations are considering the load.
When you define a load on the secondary operation, both time (setup and run time) are considering the load during estimation. That means the calculated setup time and the calcu...
Thank you for your feedback.
Currently this is not in our roadmap; however, we are tracking it and if we get more feedback and votes, we may consider it in the future.
Sincerely,
Johan Hoffmann
PM,
Microsoft.
System should prevent workers in PFE from clocking in or starting jobs when the worker's registrations have been Transferred.
The issue, "When starting jobs on the Job card device, the Started quantity is not updated when jobs are being started after registrations have been transferred"
Thank you for your feedback. Currently this is not in our roadmap; however, we are tracking it and if we get more feedback and votes, we may consider it in the future.
Sincerely,
Johan Hoffmann
PM, Microsoft
Production floor execution - attachment preview is small
Preview of attached file or note is small, It is thin although there is enough space to make preview higher and wider
Thank you for your feedback. We enhanced this feature so attahcments now are using the full space in the dialog in the production floor execution interface.
Sincerely,
Johan Hoffmann
PM, Microsoft
Make Job card terminal paper clip great again
At Job card terminal, the paper clip button, normally showing the number of attachments for the current record elsewhere is the system, always shows zero now. It shows that there are zero attachments even when there are connected attachments (to production order, operation, connected BOM lines et...
Improve subcontracting: we want multi-line PO's!
Typically a planned prod order, after firming, is created in the scheduled status. This means that any subcontracting PO has already been created. It will be line line PO just for this one prod order. Most customers don't want that. They have a lot of subcontr work they want to combine in one ...
Report feedback form should show all jobs
Report feedback form should show the jobs started in other session as well. When an active session is opened with a configuration where the parameter Lock employee is selected, then jobs started by the same employee on other terminal sessions, should be shown in the current session.
Thank you for your feedback.
Currently this is not in our roadmap; however, we are tracking it and if we get more feedback and votes, we may consider it in the future.
Sincerely,
Johan Hoffmann
PM,
Microsoft.
Formula Batch Attribute inheritance for mutiple batches consumed in Batch Order
A formula for a finished good is set to inherit the values from a raw material's consumed batch (es). If there is more than one batch consumed in a production batch, the system ignores the values of the other batches' attributes that are consumed and only transfers the values of the first batc...
Thank you for your feedback.
Currently this is not in our roadmap; however, we are tracking it and if we get more feedback and votes, we may consider it in the future.
Sincerely,
Johan Hoffmann
PM,
Microsoft.
Operations material overview form should support product variants
If you open Production Control > Operations > Current Operations (ProdRouteOprOverview) And then select an operation and open: Operation details > Materials You get to this very useful form: (ProdBOMOprNum) Unfortunately it has no capability to show product dimensions/variants – nor other typic...
Thank you for your feedback. Currently this is not in our roadmap; however, we are tracking it and if we get more feedback and votes, we may consider it in the future.
Sincerely,
Johan Hoffmann
PM, Microsoft
Administrator
Thank you for your feedback.
Currently this is not in our roadmap; however, we are tracking it and if we get more feedback and votes, we may consider it in the future.
Sincerely,
Johan Hoffmann
PM,
Microsoft.